A572 (USA, AISI, ASTM, UNS ) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt Buy, sell, suppliers search product A572 on-line
A572 Grade 42, 50, 55, 60, 65 Steel Plates Leeco Steel, LLCMaterial Properties The following material properties are ASTM specifications and will be confirmed on the Mill Test Report. Grade Yield Point (ksi) Tensile Strength (ksi) Min. 8" Elongation % 42 42 60 20 50 50 65 18 55 55 70 17 60 60 75 16 65 65 80 15 Chemical Composition The following composition properties are ASTM specifications for the A572 grades. Grade 42 + Grade 42 Carbon max 0.21%
ASTM A572 Grade 50 Carbon Steel Plate is mainly used for bridge plate,gusset plate,base plate and structural steel stiffeners. Carbon Steel ASME SA572 Grade 50 Plate are intended for riveted, bolted, or welded structures primarily in applications where extra strength or reduced end product weight is desired without foregoing strength
A572 Steel Plate Supplier - A572 Grades 42 Universal A572 Plate Universal Steel stocks A572-50 from 3/16 thick up to 4 thick, and A572-42 above 4 thick up to 6 thick. A572 is used in structural applications where strength and notch toughness are more critical than the general A36 requirements.
ASTM A36 Carbon Steel vs. ASTM A572 Grade 50 ::May 30, 2020 · Both ASTM A36 carbon steel and ASTM A572 grade 50 are iron alloys. Both are furnished in the as-fabricated (no temper or treatment) condition. They have a very high 99% of their average alloy composition in common. For each property being compared, the top bar is ASTM A36 carbon steel and the bottom bar is ASTM A572 grade 50.
1.1 This specification covers five grades of high-strength low-alloy structural steel shapes, plates, sheet piling, and bars. Grades 42 , 50 , and 55  are intended for riveted, bolted, or welded structures. Grades 60  and 65  are intended for riveted or bolted construction of bridges, or for riveted, bolted, or welded construction in other applications.
ASTM A572 Grade 50 Pipe - HYSP Steel Pipe SupplierASTM A572 Grade 50 Pipe. As you know, ASTM A572 covers five grades of high-strength low-alloy structural steel shapes, plates, sheet piling, and bars.Grades 42 , 50 , and 55  are intended for riveted, bolted, or welded structures.
ASTM A572 Grade 50 Plate, ASME A572 GR. 50 Carbon Steel ASTM A572 Gr 50 Carbon Steel Plate Specification :Width:1500-4020mm Thickness:8mm-300mm Length:3000-27000mm Supply Condition :As Rolled, Normalized Rolling, Furnace Normalizing, Vacuum Degassing, Simulated Post-Weld Heat Treatment or as per customer requirement. Impact tested :-52° C Tempering:Notch toughness can be improved by quenched cooling from hot rolling or normalizing by
ASTM A1011 SS Grade 50 or A1011 HSLAS Grade 50. The HSLAS grade is closer to an exact match to A572, but either is going have the same basic performance. The SS grade is probably more readily available. CS grades have no defined yield or tensile strength requirement.
Carbon Steel ASTM A572 Gr 45 / 50 PlatesCarbon Steel A572 Gr 45 / 50 Sheets / Plates Specification. Specification :ASTM A572 / ASME SA572 Thickness :8 mm to 300 mm Width :1500 mm to 4020 mm Length :3000 mm to 27000 mm Finish :Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) Form :Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Perforated Sheet, Chequered Plate, Strip, Flats, Blank
Speedy Metals Information for ASTM A572 Grade 50 PlateIn addition, ASTM A572 Grade 50 is noted for its increased resistance to atmospheric corrosion. Grade 50 contains more alloying elements than plain carbon steel and thus is somewhat more difficult to form. Grade 50 is more difficult to cold work, but can be successfully bent or shaped but requires more force than plain carbon steel. ANALYSIS