The most common heavy hex head screw, these steel screws meet ASTM A325 regulations for structural joints, such as mating I-beams and scaffolding. Material meets ASTM F3125 specifications for quality. Dimensions meet ASME B18.2. 6 specifications. Length is measured from under the head. Partially threaded screws come with precise threaded and unthreaded portions, allowing you to place only the
ASTM A325M Specification - Boltport FastenersThis specification covers two types of quenched and tempered steel heavy hex bolts in metric and imperial sizes for structural purpose. Metric size bolts are produced from M12 to M36 as per ASTM A325M & imperial size bolts are produced from 1/2" to 1-1/2" as per ASTM A325. These boltings are intended for used in structural connections.
The Bolt Torque Table below provides information such as tension, torque, TPI for the heavy structured bolts against its corresponding bolt sizes (ranging from 1/2 to 1 1/2). ASTM A325 is an ASTM (American Society of the International Association for Testing and Materials) International standard for heavy hex structural bolts.
Hardware ASTM A325Being that A325 type 3 bolts are made from weathering steel, the grade of nut used would be ASTM A563 Grade DH3 or C3. As far as the washers are concerned, the recommended grade is the ASTM F436 hardened washer, type 1 or 3 depending on the type of bolt grade.
Heavy Hex Structural Bolts, A325, Type 1, PlainHHSB.A325.1.P Heavy Hex Structural Bolts, A325, Type 1, Plain The information below lists the required dimensional, chemical and physical characteristics of the products in this purchase order. If the order received does not meet these requirements, it may result in a supplier corrective action request, which could jeopardize your
The ASTM A325 specification covers high strength heavy hex structural bolts from 1/2 inch diameter through 1-1/2 inch diameter. These bolts are intended for use in structural connections and therefore have shorter thread lengths than standard hex bolts. 1/2-13 X 1
Specification for Structural Joints Using ASTM A325 or Jun 23, 2000 · Specification for Structural Joints Using ASTM A325 or A490 Bolts - 2000 Format Specification for Structural Joints Using ASTM A325 or A490 Bolts - 2000 Member FREE Non-member FREE Also free from the Research Council on Structural Connections at boltcouncil. Publication Date:June 23, 2000
Specification for Structural Joints Using ASTM A325 or Specification for Structural Joints Using ASTM A325 or A490 Bolts June 30, 2004 Supersedes the June 23, 2000Specification for Structural Joints Using ASTM A325 or A490 Bolts. Prepared by RCSC Committee A.1Specifications and approved by the Research Council on Structural Connections. RESEARCH COUNCIL ON STRUCTURAL CONNECTIONS boltcouncil
Aug 01, 2014 · Specification for Structural Joints Using High-Strength Bolts August 1, 2014 (includes April 2015 Errata) Supersedes the December 31, 2009 Specification for Structural Joints Using High-Strength Bolts. Prepared by RCSC Committee A.1Specifications and approved by the Research Council on Structural Connections. boltcouncil
Structural Bolts - ASTM A325 & ASTM A490 AALL ASTM A325 - Structural Bolts, Steel, Heat Treated, 120/105-ksi Minimum Tensile Strength ASTM A490 - Structrual Bolts, Alloy Steel, Heat Treated, 150-ksi Minimum Tensile Strength Nuts and washers used in a structural joint with heavy hex structural bolts must also meet appropriate standards.
Tension Control Bolts, Twist Off Bolts, A325 & A490 Specification:A325/F1852 & A490/F2280. Finish:Type-1, Type-3 & Mechanical Galvanized. Ordering Information NOTE 2Bolts are sometimes detailed with names such as A325 HS, A325 SC, A325 X or A490 N. These names relate to connection design and bolt installation, but do not change the manufacturing requirements and are preferably not shown on bolt orders.