The test specified shall be witnessed by the purchaser's inspector before shipment of material, if so specified in the order. S1. Alternative Heat Treatment-Grade WP91S1.1 Grade WP91 shall be normalized in accordance with 7.3.5 and tempered at a temperature, to be
ASTM A106 A106M Standard Specification for Seamless of meeting the attening test requirements of Supplementary Requirement S3, if tested. 13. Hydrostatic Test 13.1 Except as allowed by 13.2, 13.3, and 13.4, each length of pipe shall be subjected to the hydrostatic test without leakage through the pipe wall. 13.2 As an alternative to the hydrostatic test
ASTM A193/A193M-06a 1.4 Supplementary Requirements S1 through S10 are provided for use when additional tests or inspection are desired. These shall apply only when specified in the purchase order. E18 Test Methods for Rockwell Hardness of Metallic Materials. E21 Test Methods for Elevated Temperature Tension Tests of Metallic Materials.
ASTM A333 Gr.1, Gr.6, Gr.8 Seamless Low-Temperature Hydrostatic or Nondestructive Electric Test ASTM A333 GR.1, GR.6, GR.8 pipe shall be subjected to the nondestructive electric test or the hydrostatic test. The type of test to be used shall be at the option of the manufacturer, unless otherwise specified in the purchase order.
ASTM A416 / A416M - 16 Standard Specification for Low 1.2 A supplementary requirement (S1) is provided for use where bond strength testing of 0.600-in. [15.24-mm] diameter Grade 270 strand for applications in prestressed ground anchors is required by the purchaser. The supplementary requirement applies only when specified in the purchase order.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.. ANSI Standard. B46.1 Surface Texture. ASME Boiler and Pressure Vessel Code. Section IX ASTM Standards. A370 Test Methods and Definitions for Mechanical Testing of Steel Products. A609/A609M Practice for Castings, Carbon, Low
ASTM A574 Specification - Boltport FastenersASTM A574/A574M covers chemical, mechanical, tensile, wedge test requirement, etc. As a part of supplementary requirement, this specification allows users to select chemical requirement specific to grades like AISI 4037, 4042, 4137, 4140, 4142, 4145, 4340, 8740, 5137M & 51B37M. ASTM A574 Supplementary Grades
ASTM A789 - SlideShareFeb 22, 2017 · SUPPLEMENTARY REQUIREMENTS The following supplementary requirement shall apply only when specied by the purchaser in the inquiry, contract, or order. S1. Pneumatic Test S1.1 The tubing shall be examined by a pneumatic test (either air underwater or pneumatic leak test) in accordance with Specication A1016/A1016M.
Flattening Test S1.1 For all pipe NPS 5 and larger in nominal size there shall S3.1 The flattening test of Specification A999/A999M shall be one product analysis made of a representative sample from be made on a specimen from one end or both ends of each pipe.
STRUCTURAL FASTENERS - Merced County, CaliforniaHardened washers ASTM F 436, Type 1, Circular, including S1 supplementary requirements Direct tension indicators ASTM F 959, Type 325, zinc-coated a Use hardened washers. b Zinc-coated nuts tightened beyond snug or wrench tight must be furnished with a dry lubricant complying with supplementary requirement S2 in ASTM A 563.
Standard Specication for Carbon Steel Forgings for ed in accordance with Supplementary Requirement S2, the material shall conform to the requirements for mechanical properties prescribed in Table 2 when tested in accordance with the latest issue of Test Methods and Denitions A 370. The largest obtainable tension test specimen as specied in Test Methods and Denitions A 370 shall be used.
dance with Supplementary Requirement S1, the purchaser should take special care to ensure that 8.2.2, Supplementary Requirement S1, andAppendix X1 are thoroughly understood. 1.3 Supplementary requirements (S1 through S6) of an optional nature are provided. These shall apply only when specied in the inquiry, contract, and order.Standard Specication for Centrifugally Cast Carbon Steel Section 12 and S1 to S9 (Supplementary Requirements), 3.1.8 Test report required (Certication Section of Speci-cation A 530/A 530M), 1 This specication is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel, and RelatedAlloys, and is the direct responsibility of Subcommittee A01.09 on Carbon Steel Tubular Products.