There are four steel grades or levels in the standard ASTM A572 . And they are ASTM A572 GR42(290), A572 GR50(345), A572 GR60(415), A572 GR65(450) . Grade 50 is a high strength, low alloy steel that finds its best application where there is need for more strength per unit of weight.
ASTM A572 Grade50,55,60 HSLA Structural Steel Plate-AGICOASTM A572 Specification refers to High-Strength Low-Alloy Steel Plate for structural building, among the 5 steel grades of 42, 50, 55, 60 and 65, Grade 50 is one most common steel in applications where need more strength and less weight, use steel plate of this grade other than ordinary carbon steel will make the steel structure with same steel strength but lighter weight.
Grade of Material HSLA Grade 50. ASTM A653/A653M HSLAS 410. Material Type Galvanized. Available Coatings Galvanized, Galvanneal, Electrogalvanized. Grade of Material HSLA Grade 60. ASTM A653/A653M HSLAS 480. Material Type Galvanized. Available Coatings Galvanized, Galvanneal, Electrogalvanized.
Alloy Chatham SteelASTM A-607 GR 50. Corrosion Resistant. Highstrength, low-alloy steels with a corrosion resistence four times greater than mild steel, intended principally for applications requiring durability, minimum maintenance, and reduced weight. 50 KSI min. yield.
Carbon & High Strength Low Alloy (HSLA) Structural Steel 13 rows · Steel Plate Products. Carbon & High Strength Low Alloy (HSLA) Structural Steel Plate. A36;
It is a high strength low alloy (HSLA) columbium-vanadium steel and is available in grades 42, 55, 60 and 65. A high-strength low-alloy steel plate that is utilized in a variety of structural applications. Carbon Steel A572 Gr 45 / 50 Sheets / Plates Specification Specification :ASTM A572 / ASME SA572
Challenges, solutions for forming HSLA steelTo meet the challenges posed by forming HSLA for today's automotive weight-to-strength ratio such a high snap-through and springback, stampers can take advantage of press and tooling features to help. These include using a hydraulic or servo-driven press to perform dwell under load; higher draw pad pressure; higher energy; installing an oversized flywheel and motor combination; increasing draw
HSLA Tubing - Valmont TubingProduced in round sizes up to 12.75" OD and in squares and rectangles up to 6.00", Valmont has the manufacturing capabilities to produce HSLA tubing up to an 80,000 psi minimum yield and UHSS tubing up to a 100,000 psi min yield.
High Strength Low Alloy (HSLA) Steel. HSLA steels were originally developed in the 1960s for large-diameter oil and gas pipelines. The line pipe used in these projects required higher strength and toughness than mild carbon steel, and good weldability provided by a low carbon equivalent. The oil & gas sector is still market where the most important applications for HSLA steels are found, but the
High-Strength Low-Alloy Steels - ASM InternationalHigh-strength low-alloy (HSLA) steels, or microalloyed steels, are designed to provide better mechanical properties and/or greater resistance to atmospheric corrosion than conventional carbon steels. They are not considered to be alloy steels in the normal sense because they are A 709 Grade 50, type 1
Hot Rolled Carbon - Olympic SteelOlympic Steel boasts a broad range of hot rolled coil, sheet and plate steel products and grades in inventory; in both Hot Roll dry and Pickled and Oiled (P&O), automotive grades, Advanced High Strength Steels (AHSS), High Strength Low Alloys (HSLA) in both ASTM and AISI standards, as well as branded products COR-TEN®, DOMEX , EX-TEN®, FREMAX® steel products and more.
High Strength Low Alloy Structural Steel Tubing Independence Tube can manufacture high-strength, low alloy (HSLA) structural steel tubing available in 50,000, 60,000 and 70,000 psi minimum yield strengths. HSLA tubing provides a greater strength to weight ratio than ASTM A500 Grades B & C. Manufactured to the dimensional tolerances of A500, HLSA