2012 IBC ASTM Standards ASTM Number Description A 240/A 240M09a . Standard Specification for Chromium and Chromium-nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels and for General Applications A 252-98 (2007) Specification for Welded and Seamless Steel Pipe Piles C 149203 Standard Specification for Concrete Roof Tile
ASTM E1592 - 05(2017) Standard Test Method for Structural ASTM E1592-05(2017), Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference, ASTM International, West Conshohocken, PA, 2017, astm
Metal roof and wall panels have many test standards they must meet under certain environmental conditions. Test standards that are specified for metal panels in our industry are ASTM E283 (air leakage) and ASTM E331 (water penetration) for wall panels, and ASTM E1680 (air leakage) and ASTM E1646 (water penetration) for roof panels. While the corresponding tests are similar, the orientation of the
Architectural Roof and Wall Products Guide SpecificationsWestern States Metal Roofing . FORMED METAL ROOF AND WALL PANELS 7/8 CORRUGATED GALVALUME ® AND ZINCALUME ® GUIDE SPECS 51 074113.13 - 1 . Architectural Roof and Wall Products . Guide Specifications . Western States Metal Roofing . 901 W. Watkins St. Phoenix, AZ 85007 . PH:602-495-0048 . FX:602-261-7726 . FORMED METAL ROOF AND WALL PANELS
Concealed Fastener Steel Roof and Wall Panel Structural Most steel roof and wall panels are manufactured from either AZ-50 aluminum-zinc alloy coated steel per ASTM A792 or G-90 galvanized steel per ASTM A653 which both satisfy the IBC material standards. The performance requirements for roof panels are defined in IBC Section 1504. The most common loads applicable to steel roof
ASTM A167Stainless and Heat-Resisting Chromium-Nickel ASTM A240Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet and Strip for Pressure Vessels ASTM A653/A653M-13Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
Integrity Testing for Roofing and Waterproofing Membranes
Low Voltage TestingHigh Voltage TestingFlood TestingSpray TestingCapacitance TestingInfrared ThermographyNuclear MeterLow voltage testing is a definitive test in that once false positives are excluded the testing provides definitive locations of breaches in the membrane tested. The equipment shows where current is following water through the membrane to the substrate below.Low voltage is a viable testing option when a non-conductive membrane is installed over a conductive deck assembly. This configuration yields a simple electrical circuit whereby the membrane is an electrical isolator and any breach in theAluminium Chequered Plate Manufacturer India, ASTM B209 ASTM A153 Zinc-Coating (Hot-Dip) on Iron and Steel Hardware. ASTM A 370 Mechanical Testing of Steel Products. ASTM A 578 Specification for Straight Beam Ultrasonic Examination of plain and Clad Steel Plates for Special Applications. ASTM A 633 Specification for Normalized High Strength Low Alloy Structural Steel Plate.
Petersen Aluminum Corp. Sheet Metal Roofing SpecificationASTM B 209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate; 2001. C. ASTM E 283 - Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen; 1991 (Reapproved 1999).
1. ASTM E2950 14 Standard Specification for Metal Canopy Systems 2. ASTM A36/A36M Specification for Carbon Structural Steel 3. ASTM A325/A325M Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi roof and wall panels, and accessories complying with requirements B. Steel Plate, Bar, or Strip:ASTM A 529/A
Steel Framing Inspection GuideCold-formed steel (CFS) studs and joists are hollow C-shaped sheet steel members that are used to frame walls, floors and roofs in residential and commercial structures. In residential designs that follow the prescriptive method outlined in building codes, structural members will be arranged in
[DOC]SECTION 074113.13 - FORMED METAL ROOF PANELS · Web viewASTM E1680 in "Air Filtration" Paragraph below has replaced ASTM E283 for testing metal roof panels; retain option to allow products to be tested in accordance with ASTM E283. Backing Plates:Provide metal backing plates at panel end splices, fabricated from material recommended by manufacturer. Roof-to-wall intersections for a distance
ASTM E 1514 - Standard Specification for Struc-tural Standing Seam Steel Roof Panel Systems. ASTM E 1592 - Standard Test Method for Struc-tural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference. ASTM E 1637 - Standard Specification for Struc-tural Standing Seam Aluminum Roof Panel Sys-tems.